產品展示

當前位置:首頁 -> 產品展示->產品展示>約翰迪爾連桿RE500608代理

約翰迪爾連桿RE500608代理

詳細描述

強鹿JOHN DEERE柴油機配件、發動機配件、發電機組:
RE507980、RE531703、RE24619、RE187966、RE205726、RE507264、RE504836、RE509036、RE533910、RE532952、RE530107、RE508971、RE523502、RE518520、RE68345、RE53307、RE62240、RE533095、RE502513、RE38009、R30402、RE521538、RE521540、RE62240、P524837、RE60021、RE507236、RE59588、RE549153、RE530870、SE501610、SE501609、RE70960

麥克福斯約翰迪爾發動機零配件

約翰迪爾 6081 低壓縮活塞

型號

數量

描述

TAR49025

1

約翰迪爾(John Deere) 強鹿6081發動機后油封/ WITH WEAR SLEEVE

TR116081

6

約翰迪爾(John Deere) 強鹿6081發動機連桿瓦(標準

TR501035

12

約翰迪爾(John Deere) 強鹿6081發動機連桿螺釘

TR74008

6

約翰迪爾(John Deere) 強鹿6081發動機連桿襯套

TR87561

4

約翰迪爾(John Deere) 強鹿6081發動機凸輪軸襯套

TRE529319

6

約翰迪爾(John Deere) 強鹿6081發動機主軸瓦(標準)

TRE529320

1

約翰迪爾(John Deere) 強鹿6081發動機止推瓦(標準)

TRE506220

1

約翰迪爾(John Deere) 強鹿6081發動機大修包

TRE508156

6

約翰迪爾(John Deere) 強鹿6081發動機活塞缸套四配套,包括活塞,活塞環,活塞銷,缸套,卡簧,阻水圈,低壓縮

TRE520036

1

約翰迪爾(John Deere) 強鹿6081發動機SEAL, 曲軸 REAR

型號

數量

描述

TR116081

6

約翰迪爾(John Deere) 強鹿6081發動機連桿瓦(標準

TR66452

12

約翰迪爾(John Deere) 強鹿6081發動機連桿螺釘

TR71918

1

約翰迪爾(John Deere) 強鹿6081發動機GASKET, OIL PAN

TRE529319

6

約翰迪爾(John Deere) 強鹿6081發動機主軸瓦(標準)

TRE529320

1

約翰迪爾(John Deere) 強鹿6081發動機止推瓦(標準)

TRE506222

1

約翰迪爾(John Deere) 強鹿6081發動機GASKET, CYL HEAD SET

TRE508156

6

約翰迪爾(John Deere) 強鹿6081發動機活塞缸套四配套,包括活塞,活塞環,活塞銷,缸套,卡簧,阻水圈,低壓縮


PowerTech
 系列
發動機和設備型號
6081

根據發動機序列號199,999

8.1L

低壓縮活塞

4802  4806

發動機型號:

6081HF001

孔徑:
4.56 in 116 mm

銷徑 Ø:
1.8742 in (+/- .0002) = 47 mm

連桿(米): 
R116340 (To ESN 86,536)
R501034 (從 86,537)
連桿(米): 
RE70688
RE64509

洋馬發動機

農業
2266
9640i WTS
3510
9650
4920
9650 CTS
6610
9660
6650
9660 CTS
7200
9660 WTS
8400
9660i WTS
8410
9680 WTS
8410T
9680i WTS
8420
9750 STS
8420T
9760STS
8520
9780 CTS
8520T
9850i WTS
9100
9976
9120
9986
9560
9996
9560 STS
CH3510
9580 WTS
CTS
9610
CTS II
9640 WTS
CTS III
9650 STS
9660 STS
9780i CTS
發動機大修包
TOK504202
(點擊查看套件內容)
TOK504202A
(點擊查看套件內容)
(13)
發動機內部修理套件
TIK504202
(點擊查看套件內容)
TIK504202A
(點擊查看套件內容)
(13)
活塞缸套組件
TRE508156
組成:
a)
TRE70689
b)
TRE503528
c)
TR57771
d)
TR116236
e)
TAR98850
f)
TE1343FN
主軸瓦
TRE529319
Std.
TRE534181
0.0115
需要6片
止推軸承
TRE529320
Std.
TRE504199
0.0115
需要1片
止推墊片
TRE61253
Std.
使用3片 ,訂購數量:1
連桿瓦
TR116081
Std.
TRE57167
0.0115
需要6片
1)
前油封
TAR49025
2)
后油封
TRE520036
3)
曲軸,齒輪
TR104587
4)
曲軸
TRE535300
(1)
TRE534314
(2)
5)
齒環
TR28811
6)
后齒輪
TR63326
1)
密封圈維修包
TRE506220
2)
襯墊套
TRE506222
3)
氣缸墊
TRE55475
4)
機油底殼墊圈
TR71918
(3)
1)
連桿襯套
TR74008
x6
2)
連桿螺栓
TR66452
x12
(4)
TR501035
x12
(4)
3)
凸輪軸襯套
TR87561
x4
4)
連桿
TRE53154
(10)
TRE535555
(11)
1)
凸輪軸塞
TR82007
2)
機油冷卻器
TAR55394
3)
挺柱
TR110126
x12
4)
緊張輪
TRE518097
(9)
TRE68715
(9)
TRE57498
(9)
1)
水泵
TRE521502
TRE521503
(12)
2)
O型圈安裝組件
TRE509463

閥門部分

進氣門
TR84618
Std.
TR93308
0.003
TR93312
0.015
排氣門
TR84619
Std.
TR93311
0.003
TR93313
0.015
1)
插入閥:進氣
TR121193
Std.
2)
插入閥:排氣
TR119132
Std.
1)
閥蓋
TT20129
2)
氣門鎖夾
TT20077
3)
屏蔽閥
TR102882
x6
(5)
TR501640
x6
(6)
1)
彈簧閥
TR91822
1)
節溫器
TAR48675
180° F
2)
節溫器外殼密封
TR136063
凸輪軸襯套
TRE60622
1)
油壓傳感器
TRE167207
(9)
2)
水溫傳感器
TRE52722
(9)
3)
曲軸傳感器
TRE519144
(9)

(1)用螺旋油泵驅動齒輪。 不要與HPCR燃油系統一起使用。

(2)帶直油泵傳動齒輪。

(3)用鋁油盤使用TR49377(RE504822)。

(4)使用TR66452桿式螺栓和機器分體式連桿,并使用帶斷裂分體式連桿的TR501035桿式螺栓。

(5)發動機ESN 199,999及以下。 僅適用于Exaust Valves。

(6)發動機ESN 200,000及以上。 僅適用于Exaust Valves。

(7)發動機ESN 199,999及以下。

(8)發動機ESN 200,000及以上。

(9)檢查應用程序是否正確使用。

(10)機器分體連桿。 使用棒螺栓TR66452。

(11)破裂的分裂連桿。 使用棒螺栓TR501035。

(12)高流量。

(13)與斷裂分體連桿一起使用。

together. 3. use jdg1145 cylinder liner service set (a) with a 2.27 kg (5.0 lb) slide hammer (b) to remove cylinder liner. important: when using jdg1145 as shown (a) to remove liners, make sure puller is properly assembled before attempting to remove liners. step in bottom plate of puller assembly should fit in id of liner. do not over-tighten liner puller to remove liners. doing so could easily break liners. 4. install liner puller (c) in liner. 5. attach a 2.27 kg (5.0 lb) slide hammer (b) to liner puller as shown&remove liner. continued on next page ctm100 (20mar01) 02-030-15 powertech 10.5 l & 12.5 l diesel engines 032001 pn=155 cylinder block, liners, pistons,&rods 02 030 16 dpsg,ouo1004,1026 –19–09sep99–2/2 rg6668 –un–05dec97 cylinder liner packing a—square packing (neoprene) b—red o-ring (silicone) c—black o-ring (viton) d—cylinder block e—cylinder liner f—coolant passage 6. remove the cylinder liner square packing (a) from liner (e). 7. remove red o-ring (b)&black o-ring (c) from cylinder block (d). ctm100 (20mar01) 02-030-16 powertech 10.5 l & 12.5 l diesel engines 032001 pn=156 cylinder block, liners, pistons,&rods 02 030 17 rg,rg34710,110 –19–03aug99–1/2 visually inspect cylinder liners rg4643 –un–05dec97 liner visual inspection a—liner pitting b—erosion c—pitting depth is one-half liner thickness d—erosion depth is one-half packing step important: if pitting has occurred, check condition of coolant. 1. inspect exterior length of liner for pitting (a). check packing step for erosion (b). if pitting/erosion is observed, measure the depth of pits&erosion with a fine wire/needle. replace piston&liner if: ? pitting depth is one-half liner thickness (c)/more. specification cylinder liner wall—thickness    9.39—9.43 mm (0.370—0.371 in.) ? erosion depth is one-half packing step (d)/more. specification cylinder liner packing step— dimension   2.14—2.30 mm (0.084—0.090 in.) note: liners are reusable if the depth of pits/erosion is less than one-half the amount specified. when installing these liners, rotate 90° from original position. the liners should be deglazed&ring sets installed on pistons. continued on next page ctm100 (20mar01) 02-030-17 powertech 10.5 l & 12.5 l diesel engines 032001 pn=157 cylinder block, liners, pistons,&rods 02 030 18 rg,rg34710,110 –19–03aug99–2/2 rg1188 –un–04dec97 liner id inspection a—cracks in the flange area b—cracks in the ring travel area 2. visually examine liner id. replace piston&liner if: ? the crosshatch honing pattern is not visible immediately below the top ring turn-around area. ? liners are pitted/contain deep vertical scratches that can be detected by the fingernail. 3. carefully examine liner for signs of fatigue, such as fine cracks in the flange area (a)&cracks in the ring travel area (b). note: inspect block for cracks/erosion in the o-ring packing areas. (see inspect&clean cylinder block, later in this group.) 4. measure liner od&compare to following specifications. cylinder liners—specification flange area—od 151.565—151.615 mm (5.9671—5.9691 in.)    upper od for seating liner—od 145.795—145.845 mm (5.7400—5.7419 in.)   . water jacket area—od 144.73—144.99 mm (5.698—5.708 in.)    lower od for seating with o-rings—od 140.397—140.447 mm (5.5274—5.5294 in.)   . rg,rg34710,111 –19–30sep97–1/2 deglaze cylinder liners r26164 –un–13dec88 deglazing liners 1. secure cylinder liner in a holding fixture. see dfrg3— cylinder liner holding fixture, in section 05, group 190 for assembly of holding fixture. 2. use d17006br flexible cylinder hone to deglaze cylinder liner. note: use honing oil along with flex hone when deglazing liners. ctm100 (20mar01) 02-030-18 powertech 10.5 l & 12.5 l diesel engines 032001 pn=158 continued on next page cylinder block, liners, pistons,&rods 02 030 19 rg,rg34710,111 –19–30sep97–2/2 r26165 –un–13dec88 liner cross-hatch 3. use d17006br hone according to instructions supplied with tool to obtain a 45° cross-hatch pattern. thoroughly clean liners after deglazing. (see clean cylinder liners, next in this group.) rg,rg34710,112 –19–30sep97–1/1 clean cylinder liners 1. use a stiff bristle brush to remove all debris, rust, and scale from od of liners, under liner flange,&in o-ring packing areas. make certain there are no nicks or burrs in areas where packings will seat. important: do not use gasoline, kerosene, or commercial solvent to clean liners. solvents will not remove all the abrasives from liner walls. 2. thoroughly clean liner id with a 50 percent solution of hot water&liquid detergent. 3. rinse thoroughly&wipe dry with a clean rag. 4. swab out liner as many times as necessary with clean sae 10w oil. 5. clean liner until a white rag shows no discoloration. ctm100 (20mar01) 02-030-19 powertech 10.5 l & 12.5 l diesel engines 032001 pn=159 cylinder block, liners, pistons,&rods 02 030 20 rg,rg34710,113 –19–01nov00–1/1 cylinder liner manufacturing date code explanation rg6091 –un–27jan92 liner date code a manufacturing four-digit date code will appear on each liner. for example, sj96 15 means the liner has a non-hardened bore&was manufactured on the 15th day of october 1996. sj96 15 s   . liner material type j    month liner was manufactured 96   . year liner was manufactured 15   . day of month liner was manufactured liner material specification: s   . non-hardened liner bore h   . hardened liner bore month liner was manufactured a    january b    february c     . march d    april e   . may f    june g   . july h   . august i    september j   . october k    november l    december year liner was manufactured: 96     . 1996 97     . 1997 etc. ctm100 (20mar01) 02-030-20 powertech 10.5 l & 12.5 l diesel engines 032001 pn=160 cylinder block, liners, pistons,&rods 02 030 21 rg,rg34710,114 –19–01nov00–1/2 disassemble piston/rod assembly and clean piston rg8400 –un–22may98 removing piston pin snap ring note: piston&ring sizes differ between engines. piston part numbers are marked on top of pistons for identification. early engines engine piston ring size 10.5 l re52836, re504801 4 mm 12.5 l re66125 4 mm later engines 10.5 l re504343 3 mm 12.5 l re503969, 3 mm re505901 1. if necessary, check piston ring end gap prior to removing rings. specification no. 1 piston compression ring (4-mm rings)—end gap  . 0.43—0.69 mm (0.017—0.027 in.) no. 2 piston compression ring (4-mm rings)—end gap  . 1.01—1.27 mm (0.040—0.050 in.) no. 1 piston compression ring (3-mm rings)—end gap  . 0.48—0.74 mm (0.019—0.029 in.) no. 2 piston compression ring (3-mm rings)—en, d gap  . 1.35—1.65 mm (0.053—0.065 in.) 2. remove piston snap rings. remove piston pin and connecting rod from piston. note: discard snap rings. do not reuse. continued on next page ctm100 (20mar01) 02-030-21 powertech 10.5 l & 12.5 l diesel engines 032001 pn=161 cylinder block, liners, pistons,&rods 02 030 22 rg,rg34710,114 –19–01nov00–2/2 rg8367 –un–09dec97 removing piston rings a—jdg967 piston ring expander b—piston ring 3. remove piston rings (b) using the jdg967 piston ring expander (a). discard rings. caution: always follow manufacturer’s instructions,&safety steps exactly. 4. clean piston ring grooves using a piston ring groove cleaning tool. important: when washing pistons, always use a stiff bristle brush—not a wire brush—to loosen carbon residue. do not bead blast ring groove areas. 5. clean pistons by any of the following methods: ? immersion-solvent “d-part”. ? hydra-jet rinse gun. ? hot water with liquid detergent soap. if cleaning with hot water&liquid detergent, soak pistons in a 50 percent solution of liquid household detergent&hot water for 30 to 60 minutes. use a stiff bristle brush—not a wire brush—to loosen carbon residue. dry with compressed air. ctm100 (20mar01) 02-030-22 powertech 10.5 l & 12.5 l diesel engines 032001 pn=162 cylinder block, liners, pistons,&rods 02 030 23 rg,rg34710,115 –19–01nov00–1/1 check piston compression ring groove wear—6105 engines rg8373 –un–21may98 checking 6105 piston ring groove (jdg1019 shown on re52836 piston) rgr24201 –un–19nov97 jdg1019 ring groove wear gauge shown a—piston with worn ring groove b—keystone ring groove c—jdg1019 ring groove wear gauge d—ring land e—gauge shoulder f—piston with good ring groove note: earlier engines with re52836&re504801 pistons have 4-mm compression rings. later engines with re504343 pistons have 3-mm compression rings. piston part numbers are marked on top of pistons for identification. use the jdg1019 ring groove wear gauge on re52836 and re504801 pistons (early engines) to check wear of top two compression ring grooves. use the jdg1335 ring groove wear gauge on re504343 pistons (later engines) to check wear of top two compression ring grooves. check each groove at several locations. gauge shoulders should not contact ring land (d) of piston. if ring grooves are worn, replace piston&liner as a set. if ring grooves are good, proceed with piston inspection. ctm100 (20mar01) 02-030-23 powertech 10.5 l & 12.5 l diesel engines 032001 pn=163 cylinder block, liners, pistons,&rods 02 030 24 rg,rg34710,116 –19–01nov00–1/1 check piston compression ring groove wear—6125 engines rg8522 –un–10dec97 using jdg1022 - top groove rg8523 –un–10dec97 using jdg1022 - second groove a—jdg1022 ring groove wear gauge b—piston with good ring groove c—acceptable clearance d—piston with worn ring groove e—gauge shoulder contacting piston ring land note: earlier engines with&re66125 pistons have 4-mm compression rings. later engines with re503969&re505901 pistons have 3-mm compression rings. piston part numbers are marked on top of pistons for identification. the illustrations to the right shows use of jdg1022 wear gauge on earlier pistons. use of jdg1335 on later pistons is similar except the two compression ring grooves are the same on these pistons&only one side of the gauge is used to check both. check grooves at several locations around the circumference of piston crown. the word “top” on gauge should always face top of piston. earlier re66125 pistons with 4-mm rings: use the jdg1022 ring groove wear gauge 昆明JohnDeere密封圈修理包RE532713的價格,濟南約翰迪爾活塞銷R517073哪里買,亳州強鹿原廠進口缸套活塞批發商,海南強鹿柴油機啟動馬達RE523502價格行情,珠海約翰迪爾發動機配件配件哪家買,牡丹江強鹿啟動機RE53186找哪家,清遠約翰迪爾4045柴油機張緊輪哪里買,湘潭JohnDeere發動機活塞RE527039代理,贛州強鹿4045柴油機連桿哪里買,阿里強鹿濾芯濾清器RE21748哪家買,汕頭強鹿曲軸齒輪R28811的價格,銅川約翰迪爾柴油發電機組啟動馬達代理商,黑河JohnDeere柴油機連桿瓦RE529318公司,徐州約翰迪爾6068柴油機凸輪軸襯套供貨商,韶關JohnDeere氣門鎖夾R520798批發,海東強鹿6090柴油機四配套價格,巴音郭楞約翰迪爾強鹿3029柴油機氣門彈簧座批發,聊城約翰迪爾8270R拖拉機發動機配件市場報價,信陽約翰迪爾R113612批發,淮安約翰迪爾強鹿節溫器RE528652供貨商,大理約翰迪爾柴油發電機組凸輪軸價格行情,河池強鹿柴油機加熱器TRE502079批發,宜春強鹿消防柴油機配件市場報價,通遼約翰迪爾缸套密封水圈AR98850哪里買,黔西南約翰迪爾挖掘機單體泵一級代理,克孜勒蘇約翰迪爾強鹿4045發動機內部修理套件信息,湘西約翰迪爾6068柴油機預熱塞公司,拉薩強鹿柴油機AT21132止推軸承批發商,伊春強鹿柴油機曲軸瓦信息,北海約翰迪爾6081發動機齒環供貨商,新界約翰迪爾聯合收割機發動機柱塞公司,濟寧強鹿柴油機凸輪軸批發價,寧德約翰迪爾拖拉機發動機發電機批發價,馬鞍山約翰迪爾拖拉機發動機活塞銷哪里買,衡水約翰迪爾3029DF128輸油泵廠家供應,黃石JohnDeere柴油機活塞銷R517073哪里買,茂名強鹿柴油機連桿瓦RE65908一級代理,阿拉善約翰迪爾6081柴油機機油泵哪家好,鶴壁強鹿曲軸齒輪R104587價格行情,吳忠強鹿柴油濾芯RE521248批發,昆明強鹿左平衡軸TRE500449廠家供應,荊門強鹿發動機噴油器公司,鹽城約翰迪爾4105柴油機渦輪增壓器廠家批發,廊坊供應美國原裝6068約翰迪爾機油濾清器RE504836價格行情,海南強鹿柴油機啟動馬達RE523502價格,畢節約翰迪爾曲軸RE506195廠家供貨,金昌強鹿6081柴油發動機前油封廠家批發,南充約翰迪爾傳感器RE522794誠信推薦,南平約翰迪爾發動機放水閥供應商,梧州強鹿6090柴油發動機進氣門廠家供應,九龍約翰迪爾發動機曲軸信息,昭通JohnDeere傳感器RE167207誠信推薦,阿克蘇強鹿柴油機連桿瓦廠家供貨,萍鄉強鹿R123461風扇皮帶批發商,廣元約翰迪爾4045柴油機輸油泵哪家買,文山johndeere約翰迪爾強鹿柴油發動機廢氣熱交換器RE521493廠家供應,深圳JohnDeere空氣加熱器廠家供應,(a), end marked “g1”, to check wear of top compression ring groove. use end marked “g2” of jdg1022 ring groove wear gauge to check wear of middle compression ring groove. if gauge shoulder contacts ring land of piston, ring groove is worn. replace piston&liner as a set. if ring grooves are good (b), proceed with piston inspection. later re503969&re505901 pistons with 3-mm rings: use jdg1335 ring groove wear gauge to check wear of top two compression rings. if gauge shoulder contacts ring land of piston, ring groove is worn. replace piston&liner as a set. if ring grooves are good (b), proceed with piston inspection. ctm100 (20mar01) 02-030-24 powertech 10.5 l & 12.5 l diesel engines 032001 pn=164 cylinder block, liners, pistons,&rods 02 030 25 rg,rg34710,117 –19–01nov00–1/1 check piston oil control ring groove wear—6105&6125 engines rg5234 –un–05dec97 measuring oil control ring groove wear note: piston&ring sizes differ between engines. piston part numbers are marked on top of pistons for identification. early engines engine piston oil control ring size 10.5 l re52836, re504801 4.8 mm 12.5 l re66125 4.8 mm later engines 10.5 l re504343 4 mm 12.5 l re503969, 4 mm re505901 1. check oil control ring-to-groove clearance by installing a new ring in groove. 2. measure clearance with a feeler gauge at several points. compare measurements with specifications given below. specification oil control ring-to-groove (re52836, re504801, re66125 pistons)—clearance 0.064—0.114 mm (0.0025—0.0045 in.)    maximum clearance  . 0.165 mm (0.0065 in.) oil control ring-to-groove (re504343, re503969 and re505901 pistons)—clearance 0.041—0.091 mm (0.0016—0.0036 in.)    maximum clearance  . 0.132 mm (0.0052 in.) note: replace piston&liner (as a set) if oil control ring clearance exceeds specifications given. ctm100 (20mar01) 02-030-25 powertech 10.5 l & 12.5 l diesel engines 032001 pn=165 cylinder block, liners, pistons,&rods 02 030 26 rg,rg34710,118 –19–13aug99–1/1 inspect piston pin&pin bore in piston rg5231 –un–05dec97 installing piston pin rg4984 –un–05dec97 piston pin bore inspection a—pin b—tapered bore c—opposite side of bore note: piston pin must be in good condition? worn beyond specification given below. 1. dip piston pin in clean engine oil. note: on 6125 engines, assemble piston crown and skirt. 2. install pin (a) through piston. pin should pass through piston using only light thumb pressure. 3. check taper in piston pin bore by inserting pin from both sides. if pin enters freely, but binds in the center, the bore could be tapered (b). 4. insert pin in piston to check for bore alignment. pin should not “click”/need to be forced into bore on opposite side (c). 5. measure piston pin&piston bore&compare to specifications. if either are not within specification, replace pin, piston,&liner. specification piston pin—od 50.772—50.787 mm (1.9989—1.9995 in.)   . piston pin bore in piston (6105)—id 50.795—50.805 mm (1.9998—2.0002 in.)   . piston skirt bushing (6125)—id 50.798—50.808 mm (1.9999—2.0003 in.)   . piston crown bushing (6125)—id 50.810—50.825 mm (2.0004—2.0010 in.)    ctm100 (20mar01) 02-030-26 powertech 10.5 l & 12.5 l diesel engines 032001 pn=166 cylinder block, liners, pistons,&rods 02 030 27 rg,rg34710,119 –19–13aug99–1/2 determine piston-to-liner clearance rg7403 –un–03nov97 measuring piston skirt a—bottom of piston dimension b—6105 skirt od 1. measure 6105 skirt od (b) at right angles to piston pin bore, 29.97 mm (1.180 in.) from the bottom of the piston (a). 2. measure 6125 engine skirt od at right angles to piston pin bore, 35.0 mm (1.38 in.) from bottom of skirt. 3. record measurement&compare measurement obtained from matching liner. specification piston skirt (6105)—od 29.97 mm (1.180 in.) from bottom of piston 126.872—126.898 mm (4.9950—4.9960 in.)   . piston skirt (6125)—od 35.0 mm (1.380 in.) from bottom of skirt 126.910—126.930 mm (4.9965—4.9972 in.)   . continued on next page ctm100 (20mar01) 02-030-27 powertech 10.5 l & 12.5 l diesel engines 032001 pn=167 cylinder block, liners, pistons,&rods 02 030 28 rg,rg34710,119 –19–13aug99–2/2 rg10049 –un–25may99 measuring liner id important: always measure liners at room temperature. 4. measure liner bore parallel to piston pin at top end of ring travel (a). 5. measure bore in same position at bottom end of ring travel (b). 6. measure bore at right angle to piston pin at top end of ring travel (c). 7. measure bore in same position at bottom end of ring travel (d). 8. compare measurements a, b, c,&d to determine if liner is tapered/out-of-round. 9. compare liner id with matched piston od. specification cylinder liner—id 126.990—127.010 mm (4.9996—5.0004 in.)   . max. out of round  . 0.020 mm (0.0008 in.) max. wear/taper (ring travel area)  . 0.030 mm (0.0012 in.) piston-to-liner clearance (new part 6105)—clearance 0.092—0.138 mm (0.0036—0.0054 in.)    max. acceptable wear   . 0.152 mm (0.0060 in.) piston-to-liner clearance (new part 6125)—clearance 0.060—0.100 mm (0.0024—0.0039 in.)    max. acceptable wear   . 0.152 mm (0.0060 in.) replace piston&liners (as a set) if they exceed wear specifications given. ctm100 (20mar01) 02-030-28 powertech 10.5 l & 12.5 l diesel engines 032001 pn=168 cylinder block, liners, pistons,&rods 02 030 29 rg,rg34710,120 –19–30sep97–1/1 measure liner flange thickness rg8199 –un–21may98 measuring liner flange thickness measure cylinder liner flange thickness at several locations&compare with specification given below. if liner flange is not within specification, use liner shims or replace piston&liner as a set. specification cylinder liner flange—thickness 9.525—9.575 mm (0.3750—0.3770 in.)    ctm100 (20mar01) 02-030-29 powertech 10.5 l & 12.5 l diesel engines 032001 pn=169 cylinder block, liners, pistons,&rods 02 030 30 rg,rg34710,121 –19–13aug99–1/3 inspect&measure connecting rod bearings rg10246 –un–30jul99 assembled rod with bearing a—rod cap b—rod c—bearings inspect rod bearings for damage of wear. important: never use new connecting rod cap screws when checking rod bearing id. use new cap screws only for final assembly of connecting rods. rod bearing-to-journal oil clearance can be checked with plastigage?, if rod is connected to crankshaft. if rod is out of engine, measure id of connecting rod bearings and compare with od of crankshaft journal. note: use plastigage? as directed by the manufacturer. the use of plastigage? will determine bearing journal clearance, but will not indicate the condition of either surface. 1. with crankshaft removed, measure connecting rod journal od at several points. 2. install connecting rod cap (a) on rod (b) with bearings (c) in correct position. 3. on tongue-and-groove connecting rods: initially tighten blind-hole cap screw, then, tighten open-hole cap screw to the following specifications. specification tongue-and-groove connecting rod cap screw—initial torque  . 27 n?m (20 lb-ft) next, tighten rod cap screws to the following specifications. specification tongue-and-groove connecting rod cap screw—final torque 75 n?m (55 lb-ft) plus 90—100° turn clockwise   . (see torque-turn connecting rod cap screws, later in this group.) plastigage is a registered trademark of dana corp. ctm100 (20mar01) 02-030-30 powertech 10.5 l & 12.5 l diesel engines 032001 pn=170 continued on next page cylinder block, liners, pistons,&rods 02 030 31 rg,rg34710,121 –19–13aug99–2/3 4. on precision joint? connecting rods: initially tighten rod cap screw closest to piston end, then tighten other cap screw to the following specifications. specification precision joint? connecting rod cap screw—torque 140 n?m (103 lb-ft) plus 90—100° turn clockwise    (see torque-turn connecting rod cap screws, later in this group.) precision joint is a trademark of deere & company rg,rg34710,121 –19–13aug99–3/3 rg3824 –un–04dec97 measuring assembled rod bearing id a—inside micrometer 5. using an inside micrometer (a), measure assembled id of bearing. 6. subtract od of each crankshaft journal from id of each respective rod bearing to obtain oil clearance. 7. compare measurements with the specifications given. specification crankshaft rod journal—od 88.844—88.874 mm (3.4980—3.4990 in.)    connecting rod bearing for crankshaft journal (assembled)—id 88.93—88.98 mm (3.501—3.502 in.)   . connecting rod bearing-to-journal (new part)— oil clearance  . 0.06—0.13 mm (0.002—0.005 in.) max. oil clearance  . 0.15 mm (0.006 in.) 8. inspect connecting rod bearings for wear/damage. if bearings are worn/not within specification, replace both connecting rod bearing&rod pin bearing. ctm100 (20mar01) 02-030-31 powertech 10.5 l & 12.5 l diesel engines 032001 pn=171 cylinder block, liners, pistons,&rods 02 030 32 rg,rg34710,122 –19–02aug99–1/4 inspect connecting rod&cap rg3749 –un–04dec97 tongue-and-groove rod&cap rg10301 –un–27aug99 precision joint? rod&cap a—tongue-and-groove joints b—cap screw hole c—precision joint? mating surfaces 1. inspect rod&cap for wear/damage, such as chips or nicks in the joint areas (a). important: do not nick the joint surfaces of rod and cap. this is very critical on precision joint? rods to ensure proper seating. never scrape joint surfaces (c) with a wire brush/other tool; the interlocking mating surfaces must be preserved. 2. inspect in&around cap screw holes (b) in cap. if any defects are found, replace rod&cap. important: if replacing a connecting rod, use the same type of joint design. do not intermix precision joint? rods and tongue-and-groove rods on the same engine. see parts catalog for recommendations. precision joint is a trademark of deere & company continued on next page ctm100 (20mar01) 02-030-32 powertech 10.5 l & 12.5 l diesel engines 032001 pn=172 cylinder block, liners, pistons,&rods 02 030 33 rg,rg34710,122 –19–02aug99–2/4 rg4982 –un–05dec97 assembled rod without bearings 3. carefully clamp rod in a soft-jawed vise (cap end upward). important: never use new connecting rod cap screws when checking rod bearing id. use new cap screws only for final assembly of connecting rods. 4. install cap without bearing inserts. 5. on tongue-and-groove connecting rods: initially tighten blind-hole cap screw, then, tighten open-hole cap screw to the following specifications. specification tongue-and-groove connecting rod cap screw—initial torque  . 27 n?m (20 lb-ft) next, tighten rod cap screws to the following specifications. specification tongue-and-groove connecting rod cap screw—final torque 75 n?m (55 lb-ft) plus 90—100° turn clockwise   . (see torque-turn connecting rod cap screws, later in this group.) 6. on precision joint? connecting rods: initially tighten rod cap screw closest to piston end, then tighten other cap screw to the following specifications. specification precision joint? connecting rod cap screw—torque 140 n?m (103 lb-ft) plus 90—100° turn clockwise    (see torque-turn connecting rod cap screws, later in this group.) precision joint is a trademark of deere & company continued on next page ctm100 (20mar01) 02-030-33 powertech 10.5 l & 12.5 l diesel engines 032001 pn=173 cylinder block, liners, pistons,&rods 02 030 34 rg,rg34710,122 –19–02aug99–3/4 rg1549 –un–20nov97 measuring assembled rod bore 7. using an inside micrometer, measure rod bore at center of bore&record measurements as follows: ? (a) at right angle to rod/cap joint. ? (b) at 45 degrees left of measurement (a). ? (c) at 45 degrees right of measurement (a). 8. compare the measurements. specification connecting rod bore (for crankshaft journal bearing)—id 93.76—93.79 mm (3.6915—3.6925 in.)    if difference between the greatest&least measurement is more than 0.038 mm (0.0015 in.), the rod&cap are out of round. replace both connecting rod&cap. rg,rg34710,122 –19–02aug99–4/4 rg8420 –un–09dec97 measuring rod center-to-center bores a—rod’s piston pin bore-to-crankshaft bore center-to-center dimension 9. measure rod’s piston pin bore-to-crankshaft bore center-to-center dimension (a)&compare with specification given. if measurement is not within specification, replace rod. specification connecting rod centerline of piston pin bore-to-crankshaft bore (new part)—dimension 263.95—264.05 mm (10.392—10.396 in.)    ctm100 (20mar01) 02-030-34 powertech 10.5 l & 12.5 l diesel engines 032001 pn=174 cylinder block, liners, pistons,&rods 02 030 35 rg,rg34710,123 –19–13aug99–1/2 inspect piston pins&rod bushings rg3172 –un–04dec97 a—connecting rod installing piston pin in rod bushing b—piston pin 1. insert piston pin (b) through piston pin bushing and carefully clamp in a soft-jawed vise. 2. rotate connecting rod (a) back&forth several times to make sure connecting rod moves freely on piston pin. 3. remove piston pin from connecting rod. continued on next page ctm100 (20mar01) 02-030-35 powertech 10.5 l & 12.5 l diesel engines 032001 pn=175 cylinder block, liners, pistons,&rods 02 030 36 rg,rg34710,123 –19–13aug99–2/2 rg4924 –un–20nov97 inspecting rod piston pin bushing bore a—tapered bore b—bell-mouthed bore 4. insert pin from either side of rod bushing. if pin is free on one end, but tight on the other, the bore could be tapered (a). if pin enters freely from both sides, but is tight in the center, bore is bell-mouthed (b). 5. inspect piston pin bushing lubrication hole in rod for damage, excessive wear/contaminants. 6. measure pin bushing id for specified clearance. specification piston pin—od 50.772—50.787 mm (1.9989—1.9995 in.)   . rod pin bore without bushing— id 55.529—55.555 mm (2.1862—2.1872 in.)   . installed rod pin bushing (before boring)—id 50.729—50.781 mm (1.9972—1.9992 in.)    installed rod pin bushing (after boring)—id 50.805—50.830 mm (2.0002—2.0012 in.)    piston pin bushing bore— out-of-round   0.038 mm (0.0015 in.) piston pin-to-bushing—oil clearance 0.017—0.059 mm (0.0007—0.0023 in.)    max. acceptable wear   . 0.076 mm (0.0030 in.) press fit of bushing in rod pin bore—press fit 0.100—0.163 mm (0.0039—0.0064 in.)   . 7. if necessary, remove&replace piston pin bushing. (see remove piston pin bushing, clean, and inspect bushing bore in this group.) ctm100 (20mar01) 02-030-36 powertech 10.5 l & 12.5 l diesel engines 032001 pn=176 cylinder block, liners, pistons,&rods 02 030 37 rg,rg34710,124 –19–30sep97–1/1 remove piston pin bushing, clean, and inspect bushing bore rg4723 –un–20nov97 removing rod piston pin bushing a—jde98-8 cup b—jde98-10 bushing remover/installer c—std36104 forcing screw important: do not use pneumatic tools to remove or install piston pin bushing. use care to properly align the jde98-10 bushing remover/installer (b) with bushing so that the connecting rod is not damaged. 1. remove the used bushing with jde98-8 cup (a), jde98-10 bushing remover/installer,&std36104 forcing screw (c) from the jde98a connecting rod bushing service set. 2. clean rod bushing bore using a medium grit emery cloth, as burrs will distort bushing. install bushing on side opposite rod burr. 3. if necessary, file a slight chamfer around bushing bore to remove any sharp edges. chamfer will also aid in bushing installation. 4. measure rod bushing bore in three/more places approximately 45° apart. specification connecting rod pin bushing bore (without bushing)—id 55.529—55.555 mm (2.1862—2.1872 in.)    connecting rod pin bushing— press fit in rod pin bore 0.100—0.163 mm (0.0039—0.0064 in.)   . important: if piston pin bushing bore diameter is not within specification/bushing has spun in rod, discard rod&replace with a new one. ctm100 (20mar01) 02-030-37 powertech 10.5 l & 12.5 l diesel engines 032001 pn=177 cylinder block, liners, pistons,&rods 02 030 38 rg,rg34710,125 –19–30sep97–1/1 install piston pin bushing rg8421 –un–09dec97 installing rod piston pin bushing a—jde98-8 cup1 b—jde98-10 bushing remover/installer1 c—jde98-9 pilot1 d—std36104 forcing screw1 e—bushing f—jde98-6 pilot1 1. lubricate connecting rod bore with clean engine oil. important: do not use power tools to install bushing. 2. assemble jde98-10 bushing remover/installer (b) with jde98-9 pilot (c). install new bushing (e) onto driver. lubricate od of bushing. install&lubricate std36104 forcing screw threads (d). 3. assemble jde98-6 pilot (f) onto driver. 4. engage forcing screw heads with threads in jde98-8 cup (a)&install new bushing. important: boring the connecting rod bushing should be done only by experienced personnel on equipment capable of maintaining bushing finish specification. 5. precision bore new bushing to specification to obtain pin-to-bushing clearance. remove all debris from boring operation. specification piston pin bushing (after boring)—id 50.805—50.830 mm (2.0002—2.0012 in.)    piston pin—od 50.772—50.787 mm (1.9989—1.9995 in.)   . piston pin-to-bushing—clearance 0.017—0.059 mm (0.0007—0.0023 in.)    1 from jde98a connecting rod bushing service set. ctm100 (20mar01) 02-030-38 powertech 10.5 l & 12.5 l diesel engines 032001 pn=178 cylinder block, liners, pistons,&rods 02 030 39 rg,rg34710,126 –19–02aug99–1/1 complete disassembly of cylinder block (if required) if complete inspection&“hot tank” cleaning of cylinder block is 臨沂約翰迪爾RE521348曲軸哪里買,欽州強鹿柴油機水泵AR97708的價格,合肥約翰迪爾連桿RE500608代理,隴南JohnDeere加大連桿瓦RE65909批發,撫順johndeere約翰迪爾強鹿柴油機節溫器廠家批發,衢州強鹿6081柴油發動機修理包找哪家,昌吉迪爾強鹿后油封re530121價格,鄂爾多斯強鹿柴油機曲軸RE505921市場報價,伊春約翰迪爾收割機RE51630空氣濾芯多少錢,吳忠JOHNDEERE強鹿3029DF120配件廠家供貨,泉州美國強鹿RE60021柴油濾芯誠信推薦,博爾塔拉強鹿RE170084皮帶張緊輪批發商,高雄約翰迪爾曲軸齒輪R104587廠家供貨,山南約翰迪爾挖掘機大修包廠家批發,required, refer to the appropriate group for removal of all external&internal mounted components listed below: 1. remove crankshaft&pulley if not previously removed. (see remove crankshaft in group 040.) 2. remove coolant pump&all remaining cooling system components. (see remove coolant pump in group 070.) 3. remove timing gear cover. (see remove timing gear cover in group 040.). remove front plate. (see remove&install cylinder block front plate earlier in this group.) 4. remove engine oil pump&all remaining lubrication system components. (see remove engine oil pump in group 060.) 5. remove all components (water gallery plugs, oil gallery plugs, bushings,&engine serial number plate) before inspecting&cleaning cylinder block. use jdg782 oil gallery plug tool to remove&install gallery plugs. ctm100 (20mar01) 02-030-39 powertech 10.5 l & 12.5 l diesel engines 032001 pn=179 cylinder block, liners, pistons,&rods 02 030 40 rg,rg34710,127 –19–09sep99–1/2 inspect&clean cylinder block rg8210 –un–21may98 cleaning head bolt threads in block note: all components, water gallery plugs,&oil gallery plugs must be removed from the cylinder block for inspection&cleaning. refer to the proper group for removal of all external and internal mounted components. 1. use d17015br o-ring groove cleaning brush/an equivalent brush to thoroughly clean all debris from cylinder liner o-ring bores. 2. remove cylinder head locating dowels, if not previously removed. clean out all threaded holes for cylinder head mounting cap screws in top deck of cylinder block. use jdg978 tap/an equivalent m16 x 2.0 tap approximately 152.4 mm (6.0 in.) long. use compressed air to remove any debris/fluid which may be present in the cap screw hole. important: if cylinder block is cleaned in a hot tank, be sure to remove any aluminum parts. aluminum parts can be damaged or destroyed by hot tank solutions. remove all serial number plates. 3. clean block thoroughly using cleaning solvent, pressure steam,/a hot tank. continued on next page ctm100 (20mar01) 02-030-40 powertech 10.5 l & 12.5 l diesel engines 032001 pn=180 cylinder block, liners, pistons,&rods 02 030 41 rg,rg34710,127 –19–09sep99–2/2 rg7142 –un–05dec97 liner counterbore depth rg10340 –un–09sep99 lap liner flange a—liner flange counterbore depth b—block c—liner support flange d—jdg1145 liner service set note: jdg1145 cylinder liner service set (d) can be used with lapping compound, as shown, to lap liner flange to blockKEY PART NO. PART NAME QTY SERIAL NO. F F F REMARKS
 1 RE57151 FUEL LINE 1 X NO. 6
 2 RE57150 FUEL LINE 1 X NO. 5
 3 RE57149 FUEL LINE 1 X NO. 4
 4 R71398 SCREW 5 X
 R58186 CLAMP 10 X
 R59305 STRAP 5 X
 R61144 STRAP 5 X
 R74030 CLAMP 1 X
 5 RE57148 FUEL LINE 1 X NO. 3
 6 RE57147 FUEL LINE 1 -081549 X NO. 2
 RE502933 FUEL LINE 1 081550- X NO. 2
 7 RE57146 FUEL LINE 1 -081549 , X NO. 1
 RE502932 FUEL LINE 1 081550- X NO. 1
 8 21H1463 CAP SCREW 2 X 0.190" X 7/8"
 R59298 STRAP 1 X
 R61145 STRAP 1 X
 R120184 STRAP 1 X
 R59297 HALF CLAMP 2 X
 9 R59298 STRAP 1 X
 R58186 CLAMP 1 X
 R71212 CLAMP 1 X
 R74804 CLAMP 1 X
 R71398 SCREW 1 X
 R61145 STRAP 1 X
 R120182 STRAP 1 X
10 21H1463 CAP SCREW 1 X 0.190" X 7/8"
 R59297 HALF CLAMP 2 X
 R59598 GASKET 2 X
11 RE55662 ABSORBER 1 X
12 24H1884 WASHER 1 X 13/32" X 13/16" X 0.120" 13/32" X
 13/16" X 0.120", (NLR)
13 19M7166 CAP SCREW 1 X M10 X 20 M10 X 20
14 RE57152 INJECTION NOZZLE 6 X (A) (ROBERT BOSCH)
 R51603 O-RING 6 X
15 R84472 WASHER 6 X 7.360 X 18.160 X 2 MM (0.290" X 0.715"
 X 0.079") 7.360 X 18.160 X 2 MM
 (0.290" X 0.715" X 0.079")
16 R504057 O-RING 6 087550- X
17 RE501970 ADAPTER 6 087550- X
18 R79604 TUBE NUT 6 087550- X
19 R51937 TUBE NUT 1 X
20 AR85519 PLUG 1 X
21 RE500803 FUEL LINE 1 087550- X
22 R77551 O-RING 6 -087549 X
23 R87082 FITTING 6 -087549 X
24 R79604 TUBE NUT 6 -087549 X
25 R79605 WASHER 6 -087549 X
26 R79606 TEE FITTING 6 -087549 X
27 R51936 SEALING WASHER 11 -087549 X
28 RE15807 FUEL LINE 2 -087549 X
29 RE15808 FUEL LINE 2 -087549 X
30 RE36421 FUEL LINE 2 -087549 X
31 R97061 TEE FITTING 1 -087549 X
(A) 2 ORANGE DOT
(2) POINT ORANGE
(2) ORANGEFARBENER PUNKT
(2) PUNTO ARANCIONE
(2) PUNTO ANARANJADO
(2) ORANGEFAERGAD PUNKT
KEY PART NO. PART NAME QTY SERIAL NO. F F F REMARKS
 1 R60277 SNAP RING 1 X
 2 R375R O-RING 1 X
 3 R60279 NUT 1 X
 4 R60278 SNAP RING 1 X
 5 .. NOZZLE HOLDER 1 X (SUB RE61593)
 6 R83720 WASHER 1 X 1.02 MM (.0402")
 R83721 WASHER 1 X 1.08 MM (.0425")
 R83722 WASHER 1 X 1.12 MM (.0441")
 R83723 WASHER 1 X 1.18 MM (.0465")
 R83724 WASHER 1 X 1.22 MM (.0480")
 R83725 WASHER 1 X 1.28 MM (.0504")
 R83726 WASHER 1 X 1.30 MM (.0512")
 R83727 WASHER 1 X 1.38 MM (.0543")
 R83728 WASHER 1 X 1.42 MM (.0559")
 R83729 WASHER 1 X 1.48 MM (.0583")
 R83730 WASHER 1 X 1.50 MM (.0591")
 R83731 WASHER 1 X 1.58 MM (.0622")
 R83732 WASHER 1 X 1.60 MM (.0630")
 R83733 WASHER 1 X 1.68 MM (.0661")
 R83734 WASHER 1 X 1.70 MM (.0669")
 R83735 WASHER 1 X 1.78 MM (.0701")
 R83736 WASHER 1 X 1.82 MM (.0717")
 R83737 WASHER 1 X 1.88 MM (.0740")
 R83738 WASHER 1 X 1.90 MM (.0748")
 R83739 WASHER 1 X 1.98 MM (.0780")
 7 R108699 SPRING 1 X
 8 R108700 SEAT 1 X
 9 R108701 PLATE 1 X
10 RE57153 NOZZLE 1 X (7 X .236)
11 R127176 NUT 1 X
12 R84472 WASHER 1 X
13 RE57152 INJECTION NOZZLE 6 X (A) (ROBERT BOSCH)
(A) (2) ORANGE DOT
(2) POINT ORANGE
(2) ORANGEFARBENER PUNKT
(2) PUNTO ARANCIONE
(2) PUNTO ANARANJADO
(2) ORANGEFAERGAD PUNKT
KEY PART NO. PART NAME QTY SERIAL NO. F F F REMARKS
 1 R51936 SEALING WASHER 1 X
 2 RE30920 FUEL LINE 1 -035177 X
 3 R97061 TEE FITTING 1 -035177 X
 4 R67364 ELBOW FITTING 1 -035177 X
 5 RE35684 FUEL LINE 1 -035177 X
 6 RE30833 FUEL LINE 1 -035177 X
 7 R91824 FITTING 1 -035177 X
 8 R48693 WASHER 1 -035177 X
 9 R51936 SEALING WASHER 3 035178- X
10 RE66000 FUEL LINE 1 035178-087549 X
 RE501262 FUEL LINE 1 087550-090585 X (SUB RE504635)
 RE504635 FUEL LINE 1 090586- X (SUB FOR RE501262)
11 RE67934 ADAPTER 1 035178- X
12 R63604 FITTING 1 035178-087549 X
 RE502650 FITTING 1 087550- X (SUB FOR R63604)
13 R121195 CAP SCREW 4 X
14 R121164 GEAR 1 X
15 R76358 O-RING 1 X
16 R114130 STUD 4 X (SUB FOR R55396, THIS APPLICATION)
17 M72490 WASHER 4 X
18 14H1090 NUT 4 X
19 AR88903 ELBOW FITTING 1 X
20 R67264 PACKING 2 X
21 R79060 O-RING 1 X (SUB FOR R73858)
22 RE509065 OIL LINE 1 X (SUB FOR RE60577)
23 T18012 ELBOW FITTING 1 X
24 RE46375 FUEL PUMP 1 X (USE WITH RE62643)
25 51M4238 SEALING RING 1 X
26 RE28217 FUEL TEMPERATURE SENSOR 1 X (SUB FOR R53899, THIS APPLICATION)
27 R98500 O-RING 1 X
28 R89014 SOLENOID 1 X (B)
29 R99047 O-RING 1 X
30 RE61658 FUEL PUMP 1 -091883 X (A) (ROBERT BOSCH) (PES6P120A720RS3354)
 RE503345 FUEL PUMP 1 091162- X (A) (ROBERT BOSCH)
31 12H296 WASHER 1 X 5.486 MM (0.216")
32 14M7297 NUT 1 X
(A) "SEE YOUR AUTHORIZED PUMP REPAIR STATION FOR PARTS NOT LISTED"
CONSULTEZ VOTRE REPARATEUR DE POMPE AGREE POUR LES PIECES NON CATALOGUE    ES
NICHT GEZEIZTE TEILE VON PUMPENWERKSTAT BEZIEHEN
PER LE PARTI NON ELENCATE, RIVOLGETEVI AL CENTRO
CONSULTE CON SU ESTACION AUTORIZADA RE PEPARACIONES DE BOMBA
RAADGOER MED EN AUTORISERAD PUMPSERVICVERKSTAD BETRAEFFANDE EJ UPPTAGNA

首頁 | 產品展示 | 公司介紹 | 客戶服務 | 技術中心 | 配件中心 | 維修中心 | 聯系我們 版權所有 湖南英珀威機械有限公司

www.mypeopleskills.com 公司地址:長沙市雨花區洞井街道中海瓏悅府1棟1401備案號: 湘ICP備18016793號-2

經營范圍:湖南,長沙發電機、發電機組維修,出租。銷售珀金斯發電機,柴油發電機,發電機組零配件等。
无码专区国产精品视频